A gloved hand holding a Zabidou inline inspection unit on a plant walkway

Steel Fabrication · Compliance

CC3 and the AS/NZS 5131construction categories

CC3 is the third of four construction categories in AS/NZS 5131, the Australian and New Zealand standard for structural steelwork fabrication and erection. The category sets how much qualification, traceability, inspection and documented evidence a piece of steelwork requires, and those obligations rise from CC1 through to CC4.

The category is nominated by the designer in the project documentation rather than chosen by the fabricator, and where the specification is silent, CC2 applies. A structure is specified at a category; a fabricator is certified at one. Zabidou supplies one part of what a higher category demands, a dimensional record of every item produced, measured on the line as it is made.

Zabidou in production today

QLD + VIC

Operating in factories across Queensland and Victoria today.

100%

Inspection coverage on finished items as they come off the line.

Silver

Associate Member, Australian Steel Institute.

Bronze

Member, National Precast Association Australia.

What sets the construction category

The construction category is derived from three inputs: the consequence of a structural failure, the service conditions the steelwork will see over its life, and the complexity of fabricating it. Appendix C of the standard, which is informative rather than normative, provides tables that turn those inputs into a category, but the category that binds is the one nominated in the project documentation.

Consequence of failure

01

The importance level of the structure, taken from the National Construction Code or AS/NZS 1170.0. The greater the consequence of a failure, the higher the category.

Service conditions

02

Whether the steelwork carries predominantly static loads, or is exposed to fatigue and seismic action across its service life.

Fabrication complexity

03

The difficulty of making the steelwork itself, covering the joints involved, the processes required and the degree of control the work demands.


What rises with the category

Each step up the categories adds obligation in three directions: who is qualified to carry out the work, what has to remain traceable afterwards, and how much of the work is inspected and recorded.

01

Qualification of the people

At CC3 welder qualification moves to AS/NZS 2980 and welding coordination to ISO 14731. The people carrying out the work hold named qualifications rather than demonstrating competence informally.

02

Traceability of the work

Welder identity and weld procedure become traceable at CC3, where neither is specified at CC1 or CC2. Material traceability has to survive cutting, so a part can still be tied back to its mill certificate after it leaves the stock length.

03

Depth of inspection and record

The inspection and test plan grows with the category, and so does the documentation handed over at completion. More of the work is checked, and more of the checking has to be evidenced.

The evidence a CC3 job leaves behind

A construction category is, in practice, an evidence requirement, and Zabidou covers the part of it that is hardest to produce after the fact. The steelwork has to be made correctly, and the making has to be provable afterwards.

Most of that evidence is paperwork generated alongside the work: qualification records, procedure registers, mill certificates, calibration records and non-conformance reports. It accumulates across a job and is handed over as a package at completion.

Dimensional evidence is the part hardest to reconstruct later. A member that was measured, found correct and signed off leaves a signature behind, but it does not leave the measurement. Where a question is raised after erection, the record of what was actually made is often the one thing nobody has.

Zabidou measures each item as it is fabricated and holds the result against that item, so the dimensional record exists without anyone writing it down. The same check runs on a steel fabrication line and on a precast concrete bed.

For a fabricator the practical gain is narrow and worth having. A dimensional claim is backed by a measurement against each member rather than by a signature, so when a certifying body, a head contractor or a client asks what was actually made, the answer is retrieved rather than reconstructed. The evidence pack at completion is assembled from records that already exist.

Welder qualification, weld procedure traceability and welding coordination sit outside what Zabidou does, and the standard remains the authority on those.

The same per-item record supports the certificate of conformance issued at handover, and the first article inspection that opens each new run.

What Zabidou checks on the line

Five checks run inside the production step, on every item that passes it. Against a construction category they produce the dimensional and surface evidence item by item, without adding a stage to the process.

Full 3D As-built vs As-planned

3D as-built comparison icon

Complete 3D measurement and verification of as-built output against a Golden Sample or design intent, for full dimensional compliance without stopping the line.

Set-out Verification

Set-out verification icon

Automated, real-time verification that components are correctly positioned before and during production, while the mould is still open or the section is still in the jig.

Surface Anomaly Detection

Surface anomaly detection icon

Inline detection of surface defects, voids and irregularities at industrial speed, fully automated and without manual inspection.

Key Dimension Measurements & Verification

Key dimension measurement icon

Precise measurement and verification of critical dimensions against a Golden Sample or the drawings, inline, in real time, at scale.

Digital Provenance

Digital provenance icon

Manufactured-unit centric digital provenance that automatically delivers the full audit history operations, financiers and customers demand.


Three ways the dimensional record gets made

The qualification and welding records required at CC3 are produced by people and filed as documents. The dimensional record is different, because it can be captured as the work happens or reconstructed afterwards, and those two options are not equivalent when the question is asked months later.

A signed checklist, a measurement taken after the fact, and a record captured on the line.
 Signed checklistMeasured after the factCaptured on the line
What it provesThat an inspection took place and who signed it.The condition of the item at the time it was measured.The condition of the item as it was made.
When it existsAt the point of signing.Only once someone goes back and measures.At the moment the item is produced.
CoverageThe items and features there was time to check.The items someone thought to revisit.Every item that comes off the line.
If it is questioned laterThe signature stands, the measurement does not exist.Re-measurement, if the item is still reachable.The record is retrieved against that item.

Common questions about CC3 and AS/NZS 5131

What is CC3 in AS/NZS 5131?

CC3 is the third of four construction categories in AS/NZS 5131, the standard covering structural steelwork fabrication and erection in Australia and New Zealand. The category determines the level of qualification, traceability, inspection and documentation the work requires.

The categories run CC1 through CC4, with obligations rising at each step. CC4 is not fully defined in the standard and is set project by project for unusual or special structures.

Who decides the construction category for a project?

The designer nominates the construction category in the project documentation. It is not selected by the fabricator, and it is not a property of the steel itself.

A single structure can carry more than one category, provided every part of it is categorised.

What happens if no construction category is specified?

CC2 applies. The standard sets CC2 as the default where the construction specification does not nominate a category.

That makes CC2 the practical baseline for a great deal of commercial and industrial steelwork, with CC3 reserved for structures where the consequence of a failure, the service conditions or the complexity of fabrication push it higher.

What is the difference between CC2 and CC3?

The step from CC2 to CC3 principally adds obligations around people and traceability. Welder qualification moves to AS/NZS 2980, welding coordination to ISO 14731, and both welder identity and weld procedure become traceable where neither is specified at the lower categories.

Inspection and documentation also deepen, so a larger share of the work is checked and a fuller record is handed over at completion.

Does a fabricator need third party certification to work at CC3?

The requirement generally comes from the project specification rather than from the category itself. Certification schemes exist, and some specifications name one or require a certifying body to hold a particular accreditation.

The practical answer is therefore found in the documents for that project. A fabricator is certified at a category as a company capability, while the structure is specified at a category by its designer.

Get in Touch

Ready to explore how ultra-vision can transform your operations? Send us a message and our team will be in touch.