A gloved hand holding a Zabidou inline inspection unit on a plant walkway

Advanced Manufacturing · Inspection

First article inspection andwhat comes after

A first article inspection is a full examination of the first item produced from a new setup, verifying every specified characteristic against the drawing before the run is released. It proves that the process, the tooling and the programme together produce a correct item.

It is a check on the setup rather than on the output. The first article establishes that the arrangement is capable of making the item correctly, which is a different question from whether every item it then makes is correct. Zabidou answers the second question, measuring each item through the run rather than only the first one.

Zabidou in production today

QLD + VIC

Operating in factories across Queensland and Victoria today.

100%

Inspection coverage on finished items as they come off the line.

Silver

Associate Member, Australian Steel Institute.

Bronze

Member, National Precast Association Australia.

What a first article actually establishes

A first article inspection answers three questions at once, which is why it carries weight and why it takes time. Each of them is about the setup rather than about the batch.

The drawing has been read correctly

01

Every specified characteristic is measured and recorded against its nominal and tolerance, which surfaces misread dimensions and superseded revisions before the run starts.

The setup can produce the item

02

Tooling, fixturing, moulds and programmes are capable of holding the required tolerances in combination, not just individually.

The result is documented

03

The report becomes the reference point for the run. Where a later item is questioned, the first article is the evidence of what the process was proven to do.


What happens to item two

The first article is thorough, documented and specific to one item. Everything made after it relies on an assumption, and that assumption is where the method is thin.

01

The setup is proven once, then trusted

Approval covers the arrangement at the moment of inspection. Tooling wears, fixtures shift and moulds move, and none of those changes announce themselves between first articles.

02

Drift is gradual and invisible

A process that leaves tolerance slowly produces items that look identical to the ones before them. Without measurement across the run, the first sign is usually a rejection at the customer.

03

Sampling covers the batch, not the item

Checks after the first article are typically a proportion. A sampling plan makes a statement about the batch; it does not tell you about the unit on the truck.

From proving the setup to measuring the output

The first article and Zabidou answer different questions, and a plant that has one still has a reason to want the other.

The first article establishes capability. It is the right method for that job, it is well established across manufacturing, and nothing about automated measurement makes it unnecessary.

What it cannot do is speak for the items produced after it. The gap between a proven setup and a correct item widens with every unit, and it is filled either by sampling, by inspection where there is time, or by measuring everything.

Zabidou measures each item as it comes off the line against a Golden Sample or the drawings, which turns the question from how the run started into what the run produced. The same check runs on a precast concrete bed and on a steel fabrication line.

For a plant that means the confidence established by the first article does not decay across the run. Tooling wear and fixture movement show up as a measurement rather than as a customer rejection, and the evidence covers every unit instead of the first one and a sample.

Taking the point directly: this replaces the tape measure, not the inspector. The first article still needs an experienced person reading a drawing carefully.

Once the first article is approved, the same checks continue on every item, which is what gives first pass yield a measured basis. The method is close to a 3D laser scan, taken at the station rather than after dispatch.

What Zabidou checks on the line

Five checks run inside the production step, on every item that passes it. Where a first article verifies the setup once, these verify the output continuously, against the same drawings or Golden Sample.

Full 3D As-built vs As-planned

3D as-built comparison icon

Complete 3D measurement and verification of as-built output against a Golden Sample or design intent, for full dimensional compliance without stopping the line.

Set-out Verification

Set-out verification icon

Automated, real-time verification that components are correctly positioned before and during production, while the mould is still open or the section is still in the jig.

Surface Anomaly Detection

Surface anomaly detection icon

Inline detection of surface defects, voids and irregularities at industrial speed, fully automated and without manual inspection.

Key Dimension Measurements & Verification

Key dimension measurement icon

Precise measurement and verification of critical dimensions against a Golden Sample or the drawings, inline, in real time, at scale.

Digital Provenance

Digital provenance icon

Manufactured-unit centric digital provenance that automatically delivers the full audit history operations, financiers and customers demand.


Proving the setup against measuring the run

These are complementary rather than competing, and the distinction is simply which question each one answers.

First article inspection, sampled checks and inline measurement across a production run.
 First articleSampled checksInline measurement
What it examinesThe first item from a new setup.A proportion of the run.Every item produced.
The question it answersCan this arrangement make it correctly?Is the batch broadly within tolerance?Was this item correct?
When it happensOnce, before the run is released.At intervals through the run.At every unit, as it is made.
What it missesEverything made after it.The units not sampled.Nothing dimensional; it is not a material test.
The green Zabidou inspection enclosure mounted over the production line at Vossloh Australia, with cast sleepers stacked in the yard beyond
A Zabidou sensor unit mounted on the line guarding at Vossloh Australia, above the sleeper moulds

Common questions about first article inspection

What is a first article inspection?

A first article inspection is a complete verification of the first item produced from a new or changed setup, measuring every specified characteristic against the drawing and recording the results before the production run is released.

It is commonly abbreviated to FAI, and the resulting document is a first article inspection report, or FAIR.

When is a first article inspection required?

Typically at the start of production for a new part, and again after any change that could affect the result: new tooling, a new mould, a design revision, a change of production location or a long gap since the last run.

The triggers are normally set out in the contract or the quality plan rather than being universal.

What is the difference between first article inspection and in-process inspection?

A first article proves the setup once, before the run. In-process inspection checks items during the run, either by sampling or by measuring each one.

One answers whether the arrangement is capable. The other answers what the arrangement actually produced.

Does a first article inspection guarantee the whole run?

No. It establishes that the setup was capable at the moment it was inspected. Tooling wear, fixture movement and mould drift all occur after approval and are not covered by it.

This is why first article inspection is normally paired with some form of ongoing check rather than relied on alone.

Who carries out the first article inspection?

Usually the manufacturer, with the report submitted to the customer or their representative for approval. Some contracts require the customer to witness it, which makes it a witness point in the inspection and test plan.

Get in Touch

Ready to explore how ultra-vision can transform your operations? Send us a message and our team will be in touch.