A gloved hand holding a Zabidou inline inspection unit on a plant walkway

Precast Concrete · Quality Assurance

Concrete testing in precastproduction

Concrete testing covers the checks a precast element passes through from the wet mix to the finished unit. Each test answers a narrow question, and the set of them together is what a plant relies on to say a batch meets specification.

They fall into three groups: tests on the fresh concrete before it is placed, tests on the hardened material once it has gained strength, and checks on the finished element itself. The first two test the material. Only the third tests the thing the customer receives, and that third group is the one Zabidou automates, measuring every element as it comes off the line.

Zabidou in production today

QLD + VIC

Operating in factories across Queensland and Victoria today.

100%

Inspection coverage on finished items as they come off the line.

Silver

Associate Member, Australian Steel Institute.

Bronze

Member, National Precast Association Australia.

Three groups of test

Grouping the tests by what they examine, rather than by when they happen, makes clear why a batch can pass everything on the sheet and still produce an element that is rejected on site.

Fresh concrete, before placing

01

Slump, temperature and air content, carried out at the point of delivery or placement. They confirm the mix arrived as ordered and is workable, and they are the last chance to reject a load before it is in the mould.

Hardened material, after curing

02

Compressive strength on cylinders or cubes, with the result arriving days later. These confirm the material reached the strength the design relied on.

The finished element

03

Dimensions, the position of cast-in items, cover depth and surface condition. This group examines the unit itself rather than a sample of the material it was made from.


What the material tests do not catch

A compliant mix does not guarantee a compliant element. The tests that attract most attention examine a sample, while the thing being supplied is the unit, and the gap between the two is where most rejections originate.

01

The sample is not the element

A cylinder tells you what the concrete can do. It says nothing about whether the element it came from was cast to the right dimensions, or whether the reinforcement sat where the drawing put it.

02

The result arrives after the decision

Strength results come back after the element has been demoulded and in many cases after it has moved. By the time the number exists, the unit has already progressed.

03

Geometry is checked by hand

Dimensions, insert position and cover are usually verified with a tape, a template and an eye. That is a different kind of check from a laboratory test, and it is rarely recorded to the same standard.

Testing the element, not just the mix

The material tests are mature, standardised and well run. What is thinner, in most plants, is the evidence about the element, and that is the gap Zabidou fills.

A precast unit is accepted or rejected on what it is, not on what it was made from. Its length, the position of its cast-in ferrules and inserts, the depth of cover over the reinforcement and the condition of its faces are the characteristics a customer measures on arrival.

Those characteristics are fixed at casting and are checked, in most plants, by a person with a tape measure working to the time available. The check is real, but it produces a signature rather than a measurement, so it cannot be revisited.

Zabidou uses lasers and cameras to measure each element as it comes off the line, recording the geometry against that unit. It does not replace a strength test or a slump test, and it is not a laboratory method. It covers the group of checks that has always been manual.

For a precast plant the gain sits in the group that decides acceptance on site. Dimensions, insert position and cover are the characteristics a customer measures on delivery, and they become the ones with a measurement behind them rather than a signature. A question raised weeks later is answered from the record rather than from memory, and a rejection argued at the gate is settled with the figure taken at casting.

The same approach runs on a precast concrete bed and on a steel fabrication line.

Results from both groups depend on curing as much as on the mix, and together they are the evidence behind a certificate of conformance.

What Zabidou checks on the line

Five checks run inside the production step, on every element that passes it. None of them is a material test. They cover the third group, the finished element, which is the group a customer measures on delivery.

Full 3D As-built vs As-planned

3D as-built comparison icon

Complete 3D measurement and verification of as-built output against a Golden Sample or design intent, for full dimensional compliance without stopping the line.

Set-out Verification

Set-out verification icon

Automated, real-time verification that components are correctly positioned before and during production, while the mould is still open or the section is still in the jig.

Surface Anomaly Detection

Surface anomaly detection icon

Inline detection of surface defects, voids and irregularities at industrial speed, fully automated and without manual inspection.

Key Dimension Measurements & Verification

Key dimension measurement icon

Precise measurement and verification of critical dimensions against a Golden Sample or the drawings, inline, in real time, at scale.

Digital Provenance

Digital provenance icon

Manufactured-unit centric digital provenance that automatically delivers the full audit history operations, financiers and customers demand.


What each group of tests actually proves

Read across the row and the division becomes clear: two of these groups describe the material, and one describes the product.

The three test groups against what each one does and does not establish.
 Fresh concreteHardened materialThe finished element
What it examinesA sample of the mix as delivered.A cylinder or cube cast from the batch.The unit that will be supplied.
When the answer arrivesAt the point of placement.Days later, after curing.At the moment the unit is produced.
What it provesThe mix is workable and as ordered.The material reached its design strength.The unit matches the drawing.
What it cannot showAnything about the finished unit.Whether the element was cast correctly.Nothing about the mix itself.
The green Zabidou inspection enclosure mounted over the production line at Vossloh Australia, with cast sleepers stacked in the yard beyond
A Zabidou sensor unit mounted on the line guarding at Vossloh Australia, above the sleeper moulds

Common questions about concrete testing

What tests are carried out on precast concrete?

Precast production typically uses slump and temperature checks on the fresh concrete, compressive strength testing on cylinders or cubes cast from the batch, and dimensional and visual checks on the finished element covering size, insert position, cover depth and surface condition.

The specific set is defined by the project specification and the inspection and test plan rather than being fixed across all jobs.

What does a concrete strength test actually prove?

It establishes the compressive strength the material reached, measured on a sample cast from the same batch and cured under controlled conditions.

It is evidence about the concrete, not about the element. A unit cast from a compliant batch can still be rejected for geometry, insert position or finish.

When is a slump test done?

At the point of delivery or placement, before the concrete goes into the mould. It measures workability and gives the last practical opportunity to reject a load.

Because it is carried out on fresh concrete, it says nothing about the strength the material will reach or about the element that results.

What is not covered by standard concrete testing?

The geometry of the finished element. Dimensions, the position of cast-in items and cover depth are fixed at casting and are usually verified manually rather than by a laboratory test.

That group of checks is the one most likely to produce a rejection on site and the one least likely to have a measurement behind it.

Does automated inspection replace concrete testing?

No. Material testing establishes what the concrete can do, and no camera or laser measures compressive strength.

Automated inline measurement covers the dimensional and surface checks on the element, which is the group that has traditionally been manual.

Get in Touch

Ready to explore how ultra-vision can transform your operations? Send us a message and our team will be in touch.